karatetenor76

Reasons to Change Door Lock You can replace the lock on your door for a variety of reasons, from increasing the security of your home to re-decorating your entryway. You might need to change locks if your key gets stuck or becomes difficult to turn. DIY novices can also change their lock. Find RepairMyWindowsAndDoors to begin. Remove the old lock The removal of the old lock from the door is a necessary step prior to installing the new lock. This is crucial when you suspect that someone else has access to the home. It is also an ideal option if you have moved into a house, experienced a break-in or received a new roommate. It is easier than you think to complete and can be done in a matter of minutes. Start by removing the screws holding the deadbolt faceplate to the frame of the door. You will need to take off the screws on both sides of the door to remove the faceplate. This will let you observe what's behind it and will give you a better idea of what to do with the remaining steps. After removing the old faceplate you will have to remove the bolt as well as the strike plate and strike plate. Remove the bolt from the door hole by using the screwdriver. If the bolt is rusted, you may need to use a chisel and smash it. If you use a chisel to remove the bolt, be careful not to damage the door frame. Before you take down the old lock, be sure that the new deadbolt and doorknob will fit into the holes on the door. Most hardware stores and big box stores sell various types of locks. They can assist you in choosing the best one to meet your needs. Get help if the lock you purchased does not fit your door. When you're removing the old lock, search for small notches or depressions in the handle or around the trim. If you can find them, slide a straightened safety pin or flat screwdriver through them to release the handle and expose the screws beneath. After taking the screw off the handle, you can begin to remove the knob. To do this, find the set screw located at the base of the knob, and loosen it. Next, you will need to remove the knob from the spindle and carefully remove the spindle from the door. Install the new lock It is a good idea to change locks on doors throughout your home periodically, especially after a burglary or when you move in with roommates. It's easy, affordable and effective to change the lock on your door. With a screwdriver and a few basic instructions the majority of people can do it themselves. Depending on the circumstances you may need to learn how to change the key of a door lock to ensure that you only have the key. You will need to purchase a new lock that has the same keyway as your current lock. You can save money by choosing to modify the lock yourself. Many locksmiths charge an extra fee for this. You can purchase an entirely new lock from a hardware store or online. Standard deadbolts are suitable for the majority of doors. However, you'll have to measure the door to make sure it will fit. Your new lock will often come with a diagram that will show how to install it on the door. The template can be used to drill the hole. It's a lot easier than having to measure each time. If the template doesn't match up with your hole you need to take it back to the hardware store to purchase an alternative. The new lock on the right side of the door. You can confirm this by inspecting the latch, which should be labelled “up” or something similar. Check that the latch is seated correctly in the latch plate, then secure it with the screws provided. If you are replacing a door knob lock, it's also important to be aware of the type of lock you're using. Some knob locks are right-handed. If you are not careful, the lock could be installed on the wrong side of your door, which will prevent it from being locked from the inside or outside. You should test the new lock once you finish. You should be capable of locking the door from both the inside as well as the outside, as well as unlock it using keys. If you're not satisfied with the result, you can always call a professional locksmith to fix it. Test the lock While a door lock that isn't able to be opened can be frustrating, it can also put your family's security at risk. It's simple to solve the majority of door lock issues by tackling the issue and lubrication. First, make sure that your key is correctly cut and that the lock isn't dirty or loose. If this doesn't resolve the issue, try applying lubrication to the door lock actuator using powdered graphite or a silicone-based grease. Then, make sure that the door lock switch, wiring harnesses and actuator connector are all functioning properly. To check this, consult the manual or wiring diagram to determine the purpose and color-coding for all the door lock switch wires. Use a digital meter or test light to determine if the actuator is receiving power and ground whenever the switches are turned on. If you observe an electric voltage switch on every switch activation, this indicates the switches are good and it's likely the actuator that requires to be replaced. If the switch appears to work but the actuator doesn't move when you turn it, it could be a problem with the cylinder. The actuator cylinder is equipped with pins that are spring loaded. They prevent the cylinder from rotating until the key is inserted which then pushes them up to match the height of the key in that area. Then, the cylinder to spin and unlock the lock body, allowing the handle to latch. If your door lock actuator is faulty, you can remove the switch and wires from the actuator by using a small screwdriver to release the bolt that locks and then separate the plastic cover which holds the electrical connector. Then disconnect the door lock actuator, and let it fall. You should be able find the two 10mm bolts that hold the actuator in place, and remove them. Once the actuator is removed, you will be able to disconnect the black electrical connector and remove it together with the actuator and lock assembly. Replace the key If your deadbolt is locked or door knob is not working, you will need to rekey it or replace it. It's not too difficult and can save you money. It is recommended to have an expert locksmith inspect the locks for any issues before you start. This will give peace of assurance that your home is safe and secure. To begin, take off the faceplate that is on the outside of the deadbolt or doorknob. If there are screws that hold the faceplate in place Use a screwdriver to take it off. Then, take off the interior faceplate by using a screwdriver with a flat head. After removing the faceplate, you can remove the bolt and screw from the lock cylinder. A locksmith can tell you whether you need to replace or rekey the lock. They can also advise you about the best security options for your home. They will also make any necessary adjustments to the door or frame to ensure that it is a perfect fit. They will also offer an assurance on their work. You must purchase a new lock key before you can rekey it. It is essential to select the correct key in the lock. Using an incorrect key could damage the internal mechanism and prevent it from functioning. To determine the size of a key, simply insert it into the lock. If the key fits flush against the plug, then it is the right size. If the pins protrude from the top of the plug, then they are too long. You may need to change the lock on your door for a variety of reasons, including: Rekeying a lock can be an affordable alternative to replacing one if you are moving into the home of a previous owner or if your keys are missing. It's also less costly than a full replacement. However, there are some instances where rekeying an lock isn't feasible. If the lock has been damaged or repeatedly jammed, for instance, it may be the right time to replace it.